OMG-POLARIS DR-160AX4 ESC - Red

• Power wire specifications: 12# 160mm x 2
  
• Engine wire specifications: 12# 160mm x 3
  
• Food sheet: None
  
• Exit sheet: None
  
• Basic specifications
  
• Continuous output current: 160A
  
• People's output current (instantaneous): 760a
  
• Battery cells: 2-3S Lipo
  
• BC: 6V / 7.4V adjustable / 4a
  
• Programming type
  
• Settings programming: Free ESC1 application (Android and Apple application)
  
• Online upgrade of the firmware: support
  
• ESC size: 37 x 38 x 31.5 mm
  
• ESC weight: 101g

1. 32 -bit microprocessor with more powerful treatment capacities and a more precise engine output.
2. Fully aluminum box with a highly effective thermal dissipation system and a high capacity for resistance to the current.
3. Many adjustable parameters supporting most of the shopping types.

Reverse mode, timing boost, turbo timing, accelerator descent, braking curve, accelerator response,

Operating mode, braking frequency, accelerator attenuation, braking response, boost trigger mode,

Width of the median point of the accelerator, front braking force.

1. The ESC has a maximum integrated beak output current of 10A. The output voltage is adjustable to 6.0V/7.4V, easily meeting the needs of powerful servos and high -voltage servos.
2. With the data recording function in real time, which allows you to check in real time the maximum ESC temperature, engine speed, voltage, timing and other data.
3. New software design with ultra-listed start-up and precise accelerator linearity.
4. Bluetooth module connected to adjust the settings and update the software via the mobile application (support for the adjustment of the parameters in real time. No need to restart the ESC)
5. Multiple protections: high voltage protection, low voltage protection, loss of accelerator signal loss, timing protection and overheating protection.

1. Reset password: When the ESC is on, press and hold the power button for about 10 seconds, the ESC will restore the Bluetooth password on the default setting 0000.
2. With RCOMG Bluetooth, by connecting the RCOMG application to the ESC, the user can program the parameters, update the firmware and check the ESC real -time data on the application.
3. Due to the Bluetooth range limit, the operational distance is approximately 10 meters. (If many metals or other strong interference signals or obstacles are present around, this can reduce operational distance.)
4. The name of Bluetooth cannot be changed.
5. Bluetooth connection will fail during the ESC accelerator calibration process.

1. Connect the ESC to the battery and the receiver correctly, then turn on the transmitter.
2. Press and hold the power button until the blue LED remains fixed on, the engine will emit a long beep at the same time, then release the power button, the red LED will light up fixed, the ESC enters calibration mode.
3. Pull the gas trigger thoroughly, the blue LED flashes three times and the engine emits a beep, the position of the gas at the bottom is recorded.
4. Push the gas trigger into the complete braking position, the blue LED flashes three times and the engine emits two beeps, the complete braking position is saved.
5. Release the gases to the neutral position, the blue LED flashes three times and the engine emits three beeps, the calibration of the gas is finished.
6. The ESC can support the calibration of the gases in reversal, if the emitter accelerator is set in reversal (this means that shooting the accelerator will go to the gas position 1000/Normally it is 2000, and push the accelerator will go to the position of the gas 2000/Normally it is 1000), then you make the calibration of the gases in the same way as usual (as above), it will have no effect on the ESC for the ESC The transmitter accelerator is in reversal. Note: No need to restart the ESC after finishing the calibration of the gases. Do not move the accelerator during the time when the blue LED flashes.